Tayota Kamri's repair since 2001
1. Operation manual and to maintenance of the car
2. Engine
2.1. Petrol engines models 1AZ-FE and 2AZ-FE
2.2. Mechanical part of engines of models 1AZ-FE and 2AZ-FE
2.2.1. General information and safety measures on removal of the power unit
2.2.2. Removal of sealant
2.2.3. The specification of types of the applied nuts and bolts
2.2.4. Service of a mechanical part of the engine
2.2.5. General repair operations
2.2.6. Dismantling, check and assembly of a head of the block of cylinders
2.2.7. Dismantling, check and assembly of the block of cylinders
2.2.7.1. Dismantling of the block of cylinders
2.2.7.2. Check of a radial side play of the conrod bearing
2.2.7.3. Replacement of inserts of radical bearings
2.2.7.4. Removal of the piston and rod assembled
2.2.7.5. Measurement of axial and radial side plays of a bent shaft and in radical bearings
2.2.7.6. Check of a gap between the piston and the cylinder
2.2.7.7. Check of a gap between a compression ring and a flute
2.2.7.8. Check of a gap in the lock of a piston finger
2.2.7.9. Check of internal diameter of an opening under a finger in the piston
2.2.7.10. Check of diameter of a piston finger
2.2.7.11. Check of landing of a piston finger
2.2.7.12. Check of a rod
2.2.7.13. Check of a kolnchaty shaft
2.2.7.14. Check of conrod and radical necks
2.2.7.15. Check of conrod bolts
2.2.7.16. Check and replacement of inserts of radical bearings
2.2.7.17. Assembly of conrod and piston group
2.2.7.18. Installation of piston rings
2.2.7.19. Installation of inserts of conrod bearings
2.2.7.20. Assembly of the block of cylinders
2.2.8. General assembly
2.3. Petrol engine of model 1MZ-FE
2.4. Mechanical part of the engine of model 1MZ-FE
2.5. Appendix
2.6. Tables
3. Transmission
4. Running gear
5. Steering
6. Brake system
7. Onboard electric equipment
8. Body
9. Schemes of electric equipment




80e768f8

2-2-7-2-proverka-radialnogo-lyufta-shatunnogo-podshipnika.html

2.2.7.2. Check of a radial side play of the conrod bearing

Uncover a rod and check a radial gap of the conrod bearing.

Fig. 2.96. Bolts of fastening of a cover of a rod


Check combination of tags on a rod and a cover of a rod to provide in the subsequent correctness of assembly. If tags are absent, then apply with a core them on covers and on rods. Turn off bolts of fastening of a cover of a rod (fig. 2.96).

Fig. 2.97. Removal of a cover of a rod


Turn off bolts of fastening of a cover of a rod. Uncover a rod, shaking it for conrod bolts (fig. 2.97).

Fig. 2.98. Installation of plastic caliber


Check a condition of working surfaces of a conrod neck and inserts. In the presence of scratches and zadir replace inserts. If necessary to a pereshlifuyta of a neck or replace a bent shaft. Install plastic caliber for measurement of gaps in sliding bearings across a conrod neck (fig. 2.98).
Establish a rod cover, having combined adjusting tags, and tighten fastening nuts (see fig. 2.97). Remove the lower cover of a rod, having turned off nuts. Measure the maximum width of the flattened calibration wire, having determined by it the size of a radial side play of a connecting rod.
Standard side play of the conrod bearing – 0,024–0,048 mm.
Limit side play of the conrod bearing – 0,080 mm.
If the gap is more than maximum, replace bearings. If necessary replace a bent shaft.

"previous page
2.2.7.1. Dismantling of the block of cylinders
following page"
2.2.7.3. Replacement of inserts of radical bearings