Tayota Kamri's repair since 2001
1. Operation manual and to maintenance of the car
2. Engine
2.1. Petrol engines models 1AZ-FE and 2AZ-FE
2.2. Mechanical part of engines of models 1AZ-FE and 2AZ-FE
2.2.1. General information and safety measures on removal of the power unit
2.2.2. Removal of sealant
2.2.3. The specification of types of the applied nuts and bolts
2.2.4. Service of a mechanical part of the engine
2.2.5. General repair operations
2.2.6. Dismantling, check and assembly of a head of the block of cylinders
2.2.7. Dismantling, check and assembly of the block of cylinders
2.2.8. General assembly
2.2.8.1. Installation of balancer shafts
2.2.8.2. Installation of a case
2.2.8.3. Installation of bolts of fastening of a head of the block of cylinders
2.2.8.4. Installation of an asterisk VVT-i
2.2.8.5. Installation of camshafts
2.2.8.6. Installation of the oil pump
2.2.8.7. Installation of an asterisk and chain of the drive of the oil pump
2.2.8.8. Installation of the piston of the cylinder No. 1 in VMT of the end of a step of compression
2.2.8.9. Installation of a chain of the drive of the mechanism of gas distribution
2.2.8.10. Installation of a rotor of the sensor of provision of a bent shaft
2.2.8.11. Installation of a cover of a chain of the drive of the mechanism of gas distribution
2.2.8.12. Installation of the oil pallet
2.2.8.13. Installation of the pump of cooling liquid
2.2.8.14. Installation of the sensor of provision of a bent shaft
2.2.8.15. Installation of a pulley of a bent shaft
2.2.8.16. Installation of the mechanism of a natyazhitel of a chain of the drive of the mechanism of gas distribution
2.2.8.17. Convertion of a natyazhitel of a chain of the drive of the mechanism of gas distribution in the working condition
2.2.8.18. Installation поршеня the first and fourth cylinders in compression step VMT
2.2.8.19. Final assembly of the unit
2.3. Petrol engine of model 1MZ-FE
2.4. Mechanical part of the engine of model 1MZ-FE
2.5. Appendix
2.6. Tables
3. Transmission
4. Running gear
5. Steering
6. Brake system
7. Onboard electric equipment
8. Body
9. Schemes of electric equipment




80e768f8

2-2-8-1-ustanovka-balansirnykh-valov.html

2.2.8.1. Installation of balancer shafts

Fig. 2.132. Correct the provision of the conducted gear wheel


Turn the conducted gear wheel No. 1 of the balancer shaft No. 1 in the direction of rotation to the limiter, having convinced that tags on gear wheels No. 1 and No. 2 are combined (fig. 2.132).

Fig. 2.133. Combination of tags on balancer shafts


Combine tags on balancer shafts No. 1 and No. 2, as shown in the figure 2.133.

Fig. 2.134. Order of tightening of bolts of fastening of a cover of the balanced mechanism


Place balancer shafts in a case. Apply a little engine oil on a carving and under heads of bolts of fastening of a cover of the balanced mechanism. Evenly, for several passes, in shown in the drawing 2.134 sequences wrap 8 bolts of fastening the moment of an inhaling of 22 N · m.
Mark paint bolts. Tighten bolts on 90 ° in the sequence stated above. Make sure that tags on bolts are located under 90 ° in relation to initial situation now.

"previous page
2.2.8. General assembly
following page"
2.2.8.2. Installation of a case