Tayota Kamri's repair since 2001
1. Operation manual and to maintenance of the car
2. Engine
2.1. Petrol engines models 1AZ-FE and 2AZ-FE
2.2. Mechanical part of engines of models 1AZ-FE and 2AZ-FE
2.2.1. General information and safety measures on removal of the power unit
2.2.2. Removal of sealant
2.2.3. The specification of types of the applied nuts and bolts
2.2.4. Service of a mechanical part of the engine
2.2.5. General repair operations
2.2.6. Dismantling, check and assembly of a head of the block of cylinders
2.2.7. Dismantling, check and assembly of the block of cylinders
2.2.8. General assembly
2.2.8.1. Installation of balancer shafts
2.2.8.2. Installation of a case
2.2.8.3. Installation of bolts of fastening of a head of the block of cylinders
2.2.8.4. Installation of an asterisk VVT-i
2.2.8.5. Installation of camshafts
2.2.8.6. Installation of the oil pump
2.2.8.7. Installation of an asterisk and chain of the drive of the oil pump
2.2.8.8. Installation of the piston of the cylinder No. 1 in VMT of the end of a step of compression
2.2.8.9. Installation of a chain of the drive of the mechanism of gas distribution
2.2.8.10. Installation of a rotor of the sensor of provision of a bent shaft
2.2.8.11. Installation of a cover of a chain of the drive of the mechanism of gas distribution
2.2.8.12. Installation of the oil pallet
2.2.8.13. Installation of the pump of cooling liquid
2.2.8.14. Installation of the sensor of provision of a bent shaft
2.2.8.15. Installation of a pulley of a bent shaft
2.2.8.16. Installation of the mechanism of a natyazhitel of a chain of the drive of the mechanism of gas distribution
2.2.8.17. Convertion of a natyazhitel of a chain of the drive of the mechanism of gas distribution in the working condition
2.2.8.18. Installation поршеня the first and fourth cylinders in compression step VMT
2.2.8.19. Final assembly of the unit
2.3. Petrol engine of model 1MZ-FE
2.4. Mechanical part of the engine of model 1MZ-FE
2.5. Appendix
2.6. Tables
3. Transmission
4. Running gear
5. Steering
6. Brake system
7. Onboard electric equipment
8. Body
9. Schemes of electric equipment




80e768f8

2-2-8-11-ustanovka-kryshki-cepi-privoda-mekhanizma-gazoraspredeleniya.html

2.2.8.11. Installation of a cover of a chain of the drive of the mechanism of gas distribution

Deleting old sealant, try not to damage contact surfaces of a cover of a chain of the GRM drive, pump of cooling liquid, a head of the block of cylinders and the block of cylinders. Using an edge and a scraper, remove old sealant from contact surfaces and from deepenings under sealant. Well clear all components before installation. Using bezosadochny solvent, clear surfaces before putting sealant.

Fig. 2.160. Places of putting sealant on a drive chain cover: 1 – sealant


Apply sealant on a GRM drive chain cover, as shown in the figure 2.160 (thickness of a layer of 3-4 mm).

Fig. 2.161. Places of putting sealant


You do not apply excess amount of sealant on contact surfaces. Details have to be collected during the time specified in the instruction for sealant use. Otherwise again remove sealant and lay new. Apply sealant to the places shown in the figure 2.161 (thickness of a layer of 2 mm).

Fig. 2.162. Locations of bolts and nuts of fastening of a cover of a chain of the drive of the mechanism of gas distribution: 1 – nuts


Establish a GRM drive chain cover. Evenly, for several passes, wrap fourteen bolts and two nuts (fig. 2.162).
Inhaling moments:
bolt "And"..... (length of 30 mm. a head on 10 mm) – 9 N · m;
bolt "In"..... (length of 30 mm, a head on 12 mm) – 21 N · m;
bolt "With"..... (length of 40 mm, a head on 14 mm) – 43 N · m;
nuts – 9 N · m.

"previous page
2.2.8.10. Installation of a rotor of the sensor of provision of a bent shaft
following page"
2.2.8.12. Installation of the oil pallet