Tayota Kamri's repair since 2001
1. Operation manual and to maintenance of the car
2. Engine
2.1. Petrol engines models 1AZ-FE and 2AZ-FE
2.2. Mechanical part of engines of models 1AZ-FE and 2AZ-FE
2.2.1. General information and safety measures on removal of the power unit
2.2.2. Removal of sealant
2.2.3. The specification of types of the applied nuts and bolts
2.2.4. Service of a mechanical part of the engine
2.2.5. General repair operations
2.2.6. Dismantling, check and assembly of a head of the block of cylinders
2.2.7. Dismantling, check and assembly of the block of cylinders
2.2.8. General assembly
2.2.8.1. Installation of balancer shafts
2.2.8.2. Installation of a case
2.2.8.3. Installation of bolts of fastening of a head of the block of cylinders
2.2.8.4. Installation of an asterisk VVT-i
2.2.8.5. Installation of camshafts
2.2.8.6. Installation of the oil pump
2.2.8.7. Installation of an asterisk and chain of the drive of the oil pump
2.2.8.8. Installation of the piston of the cylinder No. 1 in VMT of the end of a step of compression
2.2.8.9. Installation of a chain of the drive of the mechanism of gas distribution
2.2.8.10. Installation of a rotor of the sensor of provision of a bent shaft
2.2.8.11. Installation of a cover of a chain of the drive of the mechanism of gas distribution
2.2.8.12. Installation of the oil pallet
2.2.8.13. Installation of the pump of cooling liquid
2.2.8.14. Installation of the sensor of provision of a bent shaft
2.2.8.15. Installation of a pulley of a bent shaft
2.2.8.16. Installation of the mechanism of a natyazhitel of a chain of the drive of the mechanism of gas distribution
2.2.8.17. Convertion of a natyazhitel of a chain of the drive of the mechanism of gas distribution in the working condition
2.2.8.18. Installation поршеня the first and fourth cylinders in compression step VMT
2.2.8.19. Final assembly of the unit
2.3. Petrol engine of model 1MZ-FE
2.4. Mechanical part of the engine of model 1MZ-FE
2.5. Appendix
2.6. Tables
3. Transmission
4. Running gear
5. Steering
6. Brake system
7. Onboard electric equipment
8. Body
9. Schemes of electric equipment




80e768f8

2-2-8-13-ustanovka-nasosa-okhlazhdayushhejj-zhidkosti.html

2.2.8.13. Installation of the pump of cooling liquid

Fig. 2.165. Places of putting sealant on the surface of the pump of cooling liquid


Before installation clear the contact surfaces of the pump of cooling liquid of old sealant. Lay new sealant on an edge of the pump (thickness of a layer of 2-2,5 mm) (fig. 2.165).

NOTE
Remove surplus of sealant. After installation of the pump do not start the engine within two hours.


Fig. 2.166. Bolts and nuts of fastening of the pump of cooling liquid


Establish a pump housing of cooling liquid, having tightened four bolts of fastening and two nuts the moment of an inhaling of 9 N · m (fig. 2.166).

Fig. 2.167. Installation of a pulley of the pump of cooling liquid


By means of the special tool 09960-10010 (09962-01000, 09963-00700) establish a pulley of the pump of cooling liquid, having tightened four bolts of fastening the moment of an inhaling of 26 N · m (fig. 2.167).

"previous page
2.2.8.12. Installation of the oil pallet
following page"
2.2.8.14. Installation of the sensor of provision of a bent shaft