Tayota Kamri's repair since 2001
1. Operation manual and to maintenance of the car
2. Engine
2.1. Petrol engines models 1AZ-FE and 2AZ-FE
2.2. Mechanical part of engines of models 1AZ-FE and 2AZ-FE
2.2.1. General information and safety measures on removal of the power unit
2.2.2. Removal of sealant
2.2.3. The specification of types of the applied nuts and bolts
2.2.4. Service of a mechanical part of the engine
2.2.5. General repair operations
2.2.6. Dismantling, check and assembly of a head of the block of cylinders
2.2.7. Dismantling, check and assembly of the block of cylinders
2.2.8. General assembly
2.2.8.1. Installation of balancer shafts
2.2.8.2. Installation of a case
2.2.8.3. Installation of bolts of fastening of a head of the block of cylinders
2.2.8.4. Installation of an asterisk VVT-i
2.2.8.5. Installation of camshafts
2.2.8.6. Installation of the oil pump
2.2.8.7. Installation of an asterisk and chain of the drive of the oil pump
2.2.8.8. Installation of the piston of the cylinder No. 1 in VMT of the end of a step of compression
2.2.8.9. Installation of a chain of the drive of the mechanism of gas distribution
2.2.8.10. Installation of a rotor of the sensor of provision of a bent shaft
2.2.8.11. Installation of a cover of a chain of the drive of the mechanism of gas distribution
2.2.8.12. Installation of the oil pallet
2.2.8.13. Installation of the pump of cooling liquid
2.2.8.14. Installation of the sensor of provision of a bent shaft
2.2.8.15. Installation of a pulley of a bent shaft
2.2.8.16. Installation of the mechanism of a natyazhitel of a chain of the drive of the mechanism of gas distribution
2.2.8.17. Convertion of a natyazhitel of a chain of the drive of the mechanism of gas distribution in the working condition
2.2.8.18. Installation поршеня the first and fourth cylinders in compression step VMT
2.2.8.19. Final assembly of the unit
2.3. Petrol engine of model 1MZ-FE
2.4. Mechanical part of the engine of model 1MZ-FE
2.5. Appendix
2.6. Tables
3. Transmission
4. Running gear
5. Steering
6. Brake system
7. Onboard electric equipment
8. Body
9. Schemes of electric equipment




80e768f8

2-2-8-19-okonchatelnaya-sborka-agregata.html

2.2.8.19. Final assembly of the unit

Install the sensor of position of the camshaft, having tightened its moment inhalings of 9 N · m.

Fig. 2.176. Places of putting sealant


Apply new sealant to the places shown in the figure 2.176.

Fig. 2.177. Bolts of fastening of a cover of a head of the block of cylinders


Establish a cover of a head of the block of cylinders, having tightened fastening bolts the moment of an inhaling of 11 N · m (fig. 2.177).
Install the union of the oil pump (model without oil heater), having tightened its moment inhalings of 30 N · m.

Fig. 2.178. Tightening of a perepuskny bolt of the oil heater: 1 – nut


Install the oil heater, having tightened perepuskny a bolt the moment of an inhaling of 78,5 N · m, and a fastening nut – the moment of an inhaling of 9 N · m (fig. 2.178).

Fig. 2.53. Removal of an oil filter: 1 – special tool


Establish an oil filter (see fig. 2.53).
Wrap spark plugs the moment of an inhaling of 19 N · m.
Install the PCV valve, having wrapped its moment inhalings of 19 N · m.
Wrap a cover of a maslozalivny mouth.

"previous page
2.2.8.18. Installation поршеня the first and fourth cylinders in compression step VMT
following page"
2.3. Petrol engine of model 1MZ-FE