Tayota Kamri's repair since 2001
1. Operation manual and to maintenance of the car
2. Engine
2.1. Petrol engines models 1AZ-FE and 2AZ-FE
2.2. Mechanical part of engines of models 1AZ-FE and 2AZ-FE
2.2.1. General information and safety measures on removal of the power unit
2.2.2. Removal of sealant
2.2.3. The specification of types of the applied nuts and bolts
2.2.4. Service of a mechanical part of the engine
2.2.5. General repair operations
2.2.6. Dismantling, check and assembly of a head of the block of cylinders
2.2.7. Dismantling, check and assembly of the block of cylinders
2.2.8. General assembly
2.2.8.1. Installation of balancer shafts
2.2.8.2. Installation of a case
2.2.8.3. Installation of bolts of fastening of a head of the block of cylinders
2.2.8.4. Installation of an asterisk VVT-i
2.2.8.5. Installation of camshafts
2.2.8.6. Installation of the oil pump
2.2.8.7. Installation of an asterisk and chain of the drive of the oil pump
2.2.8.8. Installation of the piston of the cylinder No. 1 in VMT of the end of a step of compression
2.2.8.9. Installation of a chain of the drive of the mechanism of gas distribution
2.2.8.10. Installation of a rotor of the sensor of provision of a bent shaft
2.2.8.11. Installation of a cover of a chain of the drive of the mechanism of gas distribution
2.2.8.12. Installation of the oil pallet
2.2.8.13. Installation of the pump of cooling liquid
2.2.8.14. Installation of the sensor of provision of a bent shaft
2.2.8.15. Installation of a pulley of a bent shaft
2.2.8.16. Installation of the mechanism of a natyazhitel of a chain of the drive of the mechanism of gas distribution
2.2.8.17. Convertion of a natyazhitel of a chain of the drive of the mechanism of gas distribution in the working condition
2.2.8.18. Installation поршеня the first and fourth cylinders in compression step VMT
2.2.8.19. Final assembly of the unit
2.3. Petrol engine of model 1MZ-FE
2.4. Mechanical part of the engine of model 1MZ-FE
2.5. Appendix
2.6. Tables
3. Transmission
4. Running gear
5. Steering
6. Brake system
7. Onboard electric equipment
8. Body
9. Schemes of electric equipment




80e768f8

2-2-8-3-ustanovka-boltov-krepleniya-golovki-bloka-cilindrov.html

2.2.8.3. Installation of bolts of fastening of a head of the block of cylinders

Wrap bolts of fastening of a head of the block of cylinders.

Fig. 2.143. Order of tightening of bolts of fastening of a head of the block of cylinders


Bolts of fastening of a head of the block drag on in two stages. If one of bolts is damaged, replace it. Before installation apply a little engine oil on a carving and under heads of bolts. Evenly, for several passes, tighten ten bolts of fastening of a head of the block of cylinders the moment of an inhaling of 79 N · m in the sequence shown in the figure 2.143.
Note the bolt edge turned to a forward part of the engine. Tighten all bolts on 90 ° in the sequence stated above. Make sure that all tags of bolts are turned on 90 ° from initial situation.
Install the VVT-i valve and tighten its moment inhalings of 9 N · m.
Install camshafts.

Fig. 2.144. Installation of the lower insert of the forward bearing


Establish the lower insert of the forward bearing of the camshaft (fig. 2.144).

"previous page
2.2.8.2. Installation of a case
following page"
2.2.8.4. Installation of an asterisk VVT-i