Tayota Kamri's repair since 2001
1. Operation manual and to maintenance of the car
2. Engine
2.1. Petrol engines models 1AZ-FE and 2AZ-FE
2.2. Mechanical part of engines of models 1AZ-FE and 2AZ-FE
2.3. Petrol engine of model 1MZ-FE
2.4. Mechanical part of the engine of model 1MZ-FE
2.4.1. Service of a mechanical part of the engine
2.4.2. Check and adjustment of thermal gaps in valves
2.4.3. Removal, check and installation of a belt of the drive of the mechanism of gas distribution (GRM)
2.4.3.1. Removal of a belt of the GRM drive
2.4.3.2. Check of a belt of the GRM drive
2.4.3.3. Installation of a belt of the GRM drive
2.4.4. Removal of a head of the block of cylinders
2.4.5. Dismantling of a head of the block of cylinders
2.4.6. Assembly of a head of the block of cylinders
2.4.7. Installation of a head of the block of cylinders
2.4.8. Dismantling, check and assembly of the block of cylinders
2.5. Appendix
2.6. Tables
3. Transmission
4. Running gear
5. Steering
6. Brake system
7. Onboard electric equipment
8. Body
9. Schemes of electric equipment




80e768f8

2-4-3-1-snyatie-remnya-privoda-grm.html

2.4.3.1. Removal of a belt of the GRM drive

Weaken a bolt of fastening of the generator, turn off a nut and remove a generator arm No. 2.

Fig. 2.233. Removal of a pulley of the GRM drive: 1 – special tools


Holding a pulley of a bent shaft special tools 09213-54015 and 09950-50013, turn off a bolt of fastening of a pulley and remove a pulley (fig. 2.233).
Turn off four bolts and uncover GRM drive belt No. 1.
Remove a GRM drive belt guide.

Fig. 2.234. Removal of a cover No. 2 of a belt of the GRM drive


Uncover GRM drive belt No. 2. Turn off a bolt and remove protection of conducting from a GRM drive belt cover No. 3. Remove a clip of protection of conducting from a GRM drive belt cover No. 3. Turn off 5 bolts, release two clips of fastening and uncover No. 2 of a belt of the GRM drive (fig. 2.234).
Turn off two bolts and a nut and remove the right support of the engine.

Fig. 2.235. Combination of adjusting tags on the cogged pulley of a bent shaft and the case of the oil pump


Install the piston of the 1st cylinder in compression step VMT. Temporarily establish a bolt of fastening of a pulley of a bent shaft on a shaft. Turn a bent shaft, having combined adjusting tags on the cogged pulley of a bent shaft and the case of the oil pump (fig. 2.235).
ATTENTION
Always turn a bent shaft clockwise.
Check whether tags on cogged pulleys of camshafts coincide with tags on a GRM drive belt cover No. 3. Otherwise turn a bent shaft on one turn (360 °).
Turn off a bolt of a pulley of a bent shaft.

Fig. 2.237. Marking of tags of a belt of the GRM drive


If the belt of the GRM drive is reused, check existence on outer side of a belt of three adjusting tags and the tag specifying the direction of rotation. If tags are absent, put three adjusting tags opposite to tags on cogged pulleys distributive both cranked in bulk and a tag of the direction of rotation (fig. 2.237).
Alternately weakening, turn off two bolts, remove a natyazhitel of a belt of the GRM drive and a boot. Take off a GRM drive belt.

"previous page
2.4.3. Removal, check and installation of a belt of the drive of the mechanism of gas distribution (GRM)
following page"
2.4.3.2. Check of a belt of the GRM drive