Tayota Kamri's repair since 2001
1. Operation manual and to maintenance of the car
2. Engine
3. Transmission
3.1. Coupling
3.2. Mechanical transmission
3.3. Automatic transmission
3.4. Driving mechanism
3.4.1. General information
3.4.2. Check on the car
3.4.3. Components of the driving mechanism
3.4.4. Repair of a nave and rotary fist of a forward wheel
3.4.4.1. Removal
3.4.4.2. Installation
3.4.5. Replacement of a bolt of a nave of a forward wheel
3.4.6. Removal and installation of a nave of a back wheel
3.4.7. Removal and installation of a rotary fist of a nave of a back wheel
3.4.8. Replacement of a bolt of a nave of a back wheel
3.4.9. Dismantling of the drive of a forward wheel
3.5. Tables
4. Running gear
5. Steering
6. Brake system
7. Onboard electric equipment
8. Body
9. Schemes of electric equipment




80e768f8

3-4-4-1-snyatie.html

3.4.4.1. Removal

Remove a forward wheel.
Using special adaptation 09930-00010, turn off a nut of a nave of a forward wheel.
Disconnect the forward sensor of speed.

Fig. 3.139. Bolts of fastening of a forward support


Having turned off 2 bolts of fastening, disconnect a forward support of a disk brake from a rotary fist (fig. 3.139).
Remove a forward disk.
Using special adaptation 09628-62011, disconnect the left steering draft.
Disconnect the lower lever of a forward suspension bracket No. 1.
Using the plastic hammer, separate the drive of a forward wheel assembled from a nave of a forward wheel.

ATTENTION
You watch to damaging a cover and a rotor of the sensor of speed of ABS


Fig. 3.140. Fastening of a rotary fist and nave of a forward wheel


Turn off 2 bolts, nuts and remove a rotary fist with a nave of a forward wheel (fig. 3.140).
Turn off the forelock and a nut.

Fig. 3.141. Removal of the lower spherical hinge of a forward suspension bracket


Using special adaptation 09628-62011, remove the lower sharovy hinge of a forward suspension bracket (fig. 3.141).

Fig. 3.142. Removal of a lock ring of the internal hinge of the left shaft of the drive


Using a stripper of lock rings, remove a lock ring of the internal hinge of the left shaft of the drive (fig. 3.142).

Fig. 3.143. Removal of a nave of a forward wheel


Using special adaptation 09520-00031, remove a nave of a forward wheel (fig. 3.143).

Fig. 3.144. Removal of an internal ring (outside of) a nave of a forward wheel


Using special adaptation 09950-00020 and a press, remove an internal ring (outside of) a nave of a forward wheel (fig. 3.144).
Using a wrench of Torx (T30), turn off 4 bolts and remove the protection cover of a disk brake.
Place an internal ring (outside) on the hug bearing of a forward wheel.

Fig. 3.145. Vypressovka of the hug bearing of a forward wheel in special adaptation


Using special adaptation 09527-17011 and a press, a vypressuyta the hug bearing of a forward wheel against the stop in special adaptation (fig. 3.145).

Fig. 3.146. Vypressovka of the hug bearing of a forward wheel


Using a wrench for horizontal installation of a rotary fist, establish it on a support, as shown in the figure 3.146.

ATTENTION
Make sure that the rotary fist is located horizontally.

Using special adaptation 09950-60010 and a press, a vypressuyta the hug bearing.

"previous page
3.4.4. Repair of a nave and rotary fist of a forward wheel
following page"
3.4.4.2. Installation