Tayota Kamri's repair since 2001
1. Operation manual and to maintenance of the car
2. Engine
3. Transmission
4. Running gear
5. Steering
5.1. General information
5.2. Preliminary checks
5.2.1. Check of a side play of a steering wheel
5.2.2. Check of level of working liquid of the hydraulic booster
5.2.3. Check of pressure of working liquid of the hydraulic booster
5.2.4. Check of effort on a steering wheel
5.2.5. Pumping of system of the amplifier of steering
5.2.6. Steering mechanism components
5.2.7. Precautionary measures during the work with system of passive safety (SRS)
5.2.8. Removal and installation of a steering wheel and steering column
5.2.8.1. Removal of a steering wheel and finishing from the driver
5.2.8.2. Removal and check of a steering column
5.2.8.3. Check and replacement of the cylinder of the lock of ignition
5.2.8.4. Assembly and installation of a steering column
5.2.9. Removal and installation of the pump of the hydraulic booster of steering
5.3. Tables
6. Brake system
7. Onboard electric equipment
8. Body
9. Schemes of electric equipment




80e768f8

5-2-8-1-snyatie-rulevogo-kolesa-i-otdelki-so-storony-voditelya.html

5.2.8.1. Removal of a steering wheel and finishing from the driver

Disconnect plugs from the rechargeable battery.
Establish a steering wheel directly.
Using a face key (Torx), turn out 2 bolts of fastening of side caps with an internal hexagon.
Remove caps.

Fig. 5.17. Weakening of bolts of fastening of an overlay of a steering wheel


Weaken bolts of fastening of an overlay of a steering wheel. Weaken bolts until they are not recorded, as shown in the figure 5.17.
Take out an overlay of a steering wheel.

ATTENTION
Do not pull a slip sharply. Try not to break sockets of wires of a steering safety cushion.


Fig. 5.18. Sockets of fastening of wires of a safety cushion


Using the screw-driver, disconnect 2 sockets of fastening of wires of a steering safety cushion, as shown in the figure 5.18.
Remove an overlay of a steering wheel.

Fig. 5.19. Rule of maintenance of an overlay of a steering wheel



ATTENTION
For all the time of work, in order to avoid damages, you hold a slip a front surface (fig. 5.19) up. Do not try to dismantle the capsule of a steering safety cushion.


Fig. 5.20. Removal of a steering wheel


Apply tags on a steering wheel and the main shaft. Using the special tool, turn off a nut of fastening of a steering wheel and remove a steering wheel (fig. 5.20).

Fig. 5.21. Bolts of fastening of the top casing of a steering column


The screw-driver turn off 2 screws of fastening of the top casing of a steering column (fig. 5.21).
Having turned off three bolts, uncover the lower casing No. 2.
Having disconnected the socket, remove the regulator of light of headlights assembled.
Remove the combined switch with a spiral wire.
Having disconnected the socket, remove the screen wiper switch assembled.

NOTE
Do not sort a spiral wire and avoid hit of oil on it.


Fig. 5.22. Fastening of finishing of a threshold of a forward door


Remove finishing of a threshold of a forward door, having disconnected 7 clamps and 4 clip-on earrings of fastening (fig. 5.22).

Fig. 5.23. Fastening of a side decorative overlay of salon


Disconnect 2 clip-on earrings and remove a side decorative overlay of salon (fig. 5.23).

Fig. 5.24. Fastening of the lower finishing panel from the driver


Turn off two bolts, disconnect a cowl lock cable. Disconnect three clips of fastening and remove the lower finishing panel from the driver (fig. 5.24).
Unscrew four screws and remove an insert of the lower finishing panel.

Fig. 5.25. Fastening of finishing of a combination of devices


Turn off two screws, disconnect 2 clip-on earrings of fastening and remove finishing of a combination of devices (fig. 5.25)
Remove finishing of the lock of ignition.

"previous page
5.2.8. Removal and installation of a steering wheel and steering column
following page"
5.2.8.2. Removal and check of a steering column