Tayota Kamri's repair since 2001
1. Operation manual and to maintenance of the car
2. Engine
3. Transmission
4. Running gear
5. Steering
5.1. General information
5.2. Preliminary checks
5.2.1. Check of a side play of a steering wheel
5.2.2. Check of level of working liquid of the hydraulic booster
5.2.3. Check of pressure of working liquid of the hydraulic booster
5.2.4. Check of effort on a steering wheel
5.2.5. Pumping of system of the amplifier of steering
5.2.6. Steering mechanism components
5.2.7. Precautionary measures during the work with system of passive safety (SRS)
5.2.8. Removal and installation of a steering wheel and steering column
5.2.8.1. Removal of a steering wheel and finishing from the driver
5.2.8.2. Removal and check of a steering column
5.2.8.3. Check and replacement of the cylinder of the lock of ignition
5.2.8.4. Assembly and installation of a steering column
5.2.9. Removal and installation of the pump of the hydraulic booster of steering
5.3. Tables
6. Brake system
7. Onboard electric equipment
8. Body
9. Schemes of electric equipment




80e768f8

5-2-8-4-sborka-i-ustanovka-rulevojj-kolonki.html

5.2.8.4. Assembly and installation of a steering column

Fig. 5.33. Installation of the conducted shaft in the case steering kolonik


Using a dilator, put an internal spring ring of the conducted shaft of management and install the conducted shaft in the case of a steering column (fig. 5.33).
Put an external spring ring of the conducted shaft of management.

Fig. 5.34. Installation of the radial bearing of the conducted shaft


By means of the special tool install the radial bearing of the conducted shaft (fig. 5.34)

Fig. 5.35. Installation of an arm of fastening of the case of a steering column


Establish an arm of fastening of the case of a steering column (fig. 5.35).

NOTE
At installation use new coupling bolts with a conic head. Tighten them until heads of bolts are not cut off.


Fig. 5.36. Combination of tags of an intermediate shaft and shaft of the steering mechanism


Combine tags of an intermediate shaft and a shaft of the steering mechanism (fig. 5.36).
Insert a shaft of management into the case of an intermediate shaft.

Fig. 5.37. Combination of tags of an intermediate shaft and shaft of management of a steering column


Level tags of combination of an intermediate shaft and a shaft of management of a steering column. After that tighten a connecting bolt of fastening (fig. 5.37).

Fig. 5.38. Installation of a steering column assembled


Establish a steering column assembled and tighten 3 bolts of fastening (fig. 5.38).
Inhaling moment: 20,6 N · m.

Fig. 5.39. Installation of a steering column and intermediate shaft of steering


Establish an intermediate shaft assembled, combine tags of an intermediate shaft and an arm of a steering column and tighten a coupling bolt of fastening (fig. 5.39).
Inhaling moment: 35,3 N · m.
You make other assembly as it should be, the return to removal.
Before installation of a steering wheel correctly lay a spiral wire of the central safety cushion.
Make sure that wheels are established in the direction of the movement on a straight line.
Overwind a wire counterclockwise against the stop.

Fig. 5.40. Laying of a spiral wire of the central safety cushion


Overwind a wire clockwise on two and a half turns and combine tags, as shown in the drawing (fig. 5.40).

NOTE
The wire can be turned on two and a half turns from the central situation to the right and to the left. After installation be convinced that the provision of a steering wheel corresponds to the direction of the movement.

ATTENTION
If the overlay of a steering wheel has mechanical damages, i.e. cracks, dents or other defects, it is necessary to replace it new.
Never use the overlay of a steering wheel taken from other car. Do not sort a slip assembled with the capsule of a steering safety cushion. Replace a slip only complete new. At installation make sure that the overlay of a steering wheel is established with the effort of an inhaling regulated by the specification.


"previous page
5.2.8.3. Check and replacement of the cylinder of the lock of ignition
following page"
5.2.9. Removal and installation of the pump of the hydraulic booster of steering