Tayota Kamri's repair since 2001
1. Operation manual and to maintenance of the car
2. Engine
3. Transmission
4. Running gear
5. Steering
6. Brake system
7. Onboard electric equipment
8. Body
8.1. General information
8.2. Features of a design of a body of the Camry car
8.3. Adjustment of hinged components of a body
8.4. Removal of hinged components and decorative overlays of a body
8.4.1. Removal of a front bumper
8.4.2. Removal of a rear bumper
8.4.3. Removal and installation of a back spoiler
8.4.4. Removal and installation of the top molding
8.4.5. Removal and installation of moldings of forward and back doors
8.4.6. Removal and installation of the lower molding
8.4.7. Removal and installation of a decorative overlay of a luggage carrier
8.4.8. Removal and installation of decorative emblems and fonts
8.5. Glasses
8.6. Headlights
8.7. Screen wipers
8.8. Conditioner and heater
8.9. Tables
9. Schemes of electric equipment




80e768f8

8-4-1-snyatie-perednego-bampera.html

8.4.1. Removal of a front bumper

Fig. 8.25. Dismantling components of a front bumper: 1 – forward and side elements of the top shock-absorber of a bumper; 2 – the amplifier of a bumper from a body; 3 – lower shock-absorber of a bumper; 4 – decorative overlay of a niche of a fog lamp; 5 – фиксат


Dismantling components of a front bumper are shown in fig. 8.25.

NOTE
Carry out installation of components as it should be, the return to removal.


Fig. 8.26. Removal of a percussion cap and bolts of the top fastening of a front bumper


Turn off two bolts and take one percussion cap of the top fastening of a front bumper (fig. 8.26).

Fig. 8.27. Removal of a percussion cap of side fastening of a front bumper


Take out two percussion caps of side fastening of a bumper from two parties. To remove a percussion cap, extend it a little forward and turn a percussion cap hat on 90 ° (fig. 8.27).

Fig. 8.28. Bolts of the lower fastening of a front bumper


Turn off and remove nine bolts of the lower fastening of a bumper (fig. 8.28).

Fig. 8.29. A detachment of clips of fastening of a bumper to a body


Wring out three clips from each party on the case of a bumper and disconnect them from a body as it is shown in the figure 8.29. Disconnect also sockets of fog lamps (if they are established).
Remove a bumper.

Fig. 8.30. Clip of a forward decorative overlay of a bumper


Wring out two clips and remove a forward decorative overlay of a bumper (fig. 8.30).

Fig. 8.31. Removal of an overlay of registration plate


Turn off two screws of fastening and remove an overlay of registration plate (fig. 8.31).

Fig. 8.32. Removal of a decorative overlay of a fog lamp


Turn off two screws of fastening from each party and remove decorative overlays of fog lamps (fig. 8.32).
Take out fog lamps from the bumper case (if they are established).

Fig. 8.33. Removal of the lower shock-absorber of a bumper


Remove the lower shock-absorber of a bumper (fig. 8.33).

Fig. 8.34. Removal of the amplifier of a bumper from a body


Remove five percussion caps, turn off six bolts of fastening and remove the amplifier of a bumper from a body (fig. 8.34).

Fig. 8.35. Removal of a forward element of the top shock-absorber of a bumper


Turn off two bolts and two nuts of fastening and remove a forward element of the top shock-absorber of a bumper (fig. 8.35).

Fig. 8.36. Removal of a side element of the top shock-absorber of a bumper


Turn off two nuts of fastening from each party of a body and remove side elements of the top shock-absorber of a bumper (fig. 8.36).
You make installation as it should be, the return to removal.
Moment of an inhaling of nuts of fastening of a side element of the top shock-absorber of a bumper: 8.5 N · m.
Moment of an inhaling of nuts and bolts of fastening of a forward element of the top shock-absorber of a bumper: 8.5 N · m.
The moment of an inhaling of bolts of fastening of the amplifier of a bumper from a body: 34 N · m.

"previous page
8.4. Removal of hinged components and decorative overlays of a body
following page"
8.4.2. Removal of a rear bumper